Hide filters
Filters 0
Order by:
Filters 0
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
Men's waterproof mountain hiking jacket - MH150

QUECHUA

8540225

Men's waterproof mountain hiking jacket - MH150

₪210.00
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
  • Men's waterproof mountain hiking jacket - MH150
Men's waterproof mountain hiking jacket - MH150
Color :
Size :
Not available online
At the foot of Mont Black, our team designed this waterproof jacket for occasional hikes, protecting you from storms in the mountains.

BENEFITS

Waterproof

Protects from a storm
2.5 layer membrane,
10000 mm Schmerber

Breathability

Perspiration wicking component (RET=10)

Lightweight

Only 490 gr in size L

Anatomic design

Drawcord at jacket hem. Elasticated cuffs. Adjustable hood

Pockets

2 zipped hand pockets, 1 zipped inside pocket, 1 inside pocket

TECHNICAL INFORMATIONS

Cut

Standard cut. The inner volume allows you to wear it over a warm 2nd warm layer such as a pullover or fleece.

Hood

Adjustable height with an elastic cord and tightening toggle.
Adjustable depth using a Velcro strip positioned at the back of the hood.
Visor at the top of the hood for good face protection.

Main component

2.5 layers with membrane

MEMBRANE

The waterproof rating of a product depends on the following two main criteria: its component and its construction.
This product was made with a membrane.
This is a kind of very thin plastic film (polyurethane) that makes the component waterproof while remaining breathable.
It has the advantage of being flexible, lightweight and breathable.

LAYER DESIGN

2.5 layer design: The membrane is glued under the outer fabric and protected inside by a fine film. We use it for light jacket.

COMPONENT WATERPROOFING

Laboratory tests are conducted to guarantee the waterproof rating of a component. This is done by measuring the fabric's resistance to water pressure expressed in terms of the height of a water column in mm (based on the ISO 811 standard). The higher the water pressure, the more waterproof the fabric.
A component with a waterproof rating of 10,000 mm can therefore withstand the pressure exerted by a 10,000 mm column of water. This is also equivalent to 10,000 Schmerbers.

JACKET WATERPROOFING

We conduct laboratory tests that simulate rainfall scenarios in order to guarantee the jacket's waterproof rating.
This garment has been validated in a shower test under 100 L/sqm/hr of water for 3 hours. This test reproduces the average conditions of a mountain storm.

BREATHABILITY

Component breathability is measured by its thermal evaporative resistance (RET).
This is its capacity to let water vapour generated by the body during physical activity escape and therefore avoid water accumulating on the skin.
The lower the RET, the more breathable the fabric.

RET ≤ 6: very breathable fabric
RET ≤ 12: breathable fabric
RET ≤ 20: not very breathable fabric
This product was assessed at 10 RET

HOW TO RESTORE THE WATER-REPELLENT PROPERTIES

A fabric is water repellent when it allows water slide over its surface without seeping in. The fabric does not soak up water and therefore remains lightweight and breathable. The water repellent property is achieved by treating the fabric's exterior. This treatment needs to be renewed during the lifetime of the garment. The water-repellent property can be reactivated by putting the jacket in the tumble dryer for 10 minutes on low heat.
You can also use the waterproof spray (ref 855490)

Product design: our expertise

Our Quechua global design centre is based in Passy, at the foot of Mont-Blanc in Haute Savoie.
This location makes it a real meeting place for our teams (designers, product managers, engineers, etc) and outdoor sports enthusiasts.
A great asset for designing your mountain walking products and providing you with all our expertise.

WHY CHOOSE RECYCLED POLYESTER?

By recycling plastic bottles or second-hand textiles to produce our polyester, we have reduced the utilisation of oil-based resources while preserving the quality and performance of the material during your mountain hikes.